Refine Your Search

Topic

Author

Affiliation

Search Results

Journal Article

Soot Emission Measurements and Validation of a Mean Value Soot Model for Common-Rail Diesel Engines during Transient Operation

2009-06-15
2009-01-1904
Measurements of the soot emissions and engine operating parameters from a diesel engine during transient operation were used to investigate the influence of transient operation on the soot emissions, as well as to validate a realtime mean value soot model (MVSM, [1]) for transient operation. To maximize the temporal resolution of the soot emission and engine parameter measurements (in particular EGR), fast instruments were used and their dynamic responses characterized and corrected. During tip-in transients, an increase in the soot emissions was observed due to a short term oxygen deficit compared to steady-state operation. No significant difference was seen between steady-state and transient operation for acceleration transients. When the MVSM was provided with inputs of sufficient temporal resolution, it was capable of reproducing the qualitative and, in part, quantitative soot emission trends.
Technical Paper

Development and Validation of a Phenomenological Mean Value Soot Model for Common-Rail Diesel Engines

2009-04-20
2009-01-1277
A mean value soot model (MVSM) was developed and validated for the realtime prediction of the raw, engine-out soot emissions from common rail diesel engines. Through the consideration of five representative states during the combustion cycle, the developed MVSM determines the engine out soot emissions based on the soot formation and oxidation processes, using only parameters available from a standard engine control unit. 16 model parameters are used to describe the engine, fuel, and combustion characteristics, and must be determined for each engine and fuel combination. The MVSM was parameterized and validated using the measured soot emissions from two different engines operating with a total of three different fuels. After parameterization, the MVSM was capable of qualitatively and quantitatively reproducing the soot emissions for operating points throughout the entire operating map, including for operating regimes not considered during the parameterization.
Technical Paper

Predictive Phenomenological C.I. Combustion Modeling Optimization on the Basis of Bio-Inspired Algorithms

2005-04-11
2005-01-1119
A new approach within the well-known trade-off in combustion process simulations between computational efforts (and thus the capability for engine operating map calculations) on the one hand, and accuracy of predictions on the other, has been developed and applied successfully to diesel combustion, in particular to energy release and pollutant formation. Using phenomenological models in combination with bio-inspired algorithms (for parameter identification), it is now possible to predict thermal, chemical and injection related engine characteristics over an entire operating map including different types of fuel (e.g. diesel, water-in-diesel emulsions and oxygenated diesel).
Technical Paper

A Quasi-Dimensional Model for Estimating the Influence of Hydrogen-Rich Gas Addition on Turbulent Flame Speed and Flame Front Propagation in IC-SI Engines

2005-04-11
2005-01-0232
Addition of hydrogen-rich gas to gasoline in internal combustion engines is gaining increasing interest, as it seems suitable to reach near-zero emission combustion, able to easily meet future stringent regulations. Bottled gas was used to simulate the output of an on-board reformer (21%H2, 24%CO, 55%N2). Measurements were carried out on a 4-stroke, 2-cylinder, 0.5-liter engine, with EGR, in order to calculate the heat release rate through a detailed two-zone model. A quasi-dimensional model of the flame was developed: it consists of a geometrical estimate of the flame surface, which is then coupled with the heat release rate. The turbulent flame speed can then be inferred. The model was then applied to blends of gasoline with hydrogen-rich gas, showing the effect on the flame speed and transition from laminar to turbulent combustion.
Technical Paper

Clean Engine Vehicle A Natural Gas Driven Euro-4/SULEV with 30% Reduced CO2-Emissions

2004-03-08
2004-01-0645
The goal of the Clean Engine Vehicle project (CEV) was the conversion of a gasoline engine to dedicated natural gas operation in order to achieve a significant reduction in CO2 emissions. The targeted reduction was 30% compared with a gasoline vehicle with similar performance. Along with the reduction in emissions, the second major requirement of the project, however, was compliance of the results with Euro-4 and SULEV emission limits. The project entailed modifications to the engine and the pre-existing model-based engine control system, the introduction of an enhanced catalytic converter and downsizing and turbocharging of the engine. As required by the initiators of the project, all components used were commonly available, some of them just being optimized or modified for natural gas operation.
Technical Paper

Influence of Hydrogen-Rich-Gas Addition on Combustion, Pollutant Formation and Efficiency of an IC-SI Engine

2004-03-08
2004-01-0972
The addition of hydrogen-rich gas to gasoline in an Internal Combustion Engine seems to be particularly suitable to arrive at a near-zero emission Otto engine, which would be able to easily meet the most stringent regulations. In order to simulate the output of an on-board reformer that partially oxidizes gasoline, providing the hydrogen-rich gas, a bottled gas has been used. Detailed results of our measurements are here shown, such as fuel consumption, engine efficiency, exhaust emissions, analysis of the heat release rates and combustion duration, for both pure gasoline and blends with reformer gas. Additionally simulations have been performed to better understand the engine behaviour and NOx formation.
Technical Paper

Advanced Emission and Fuel Economy Concept Using Combined Injection of Gasoline and Hydrogen in SI-Engines

2004-03-08
2004-01-1270
In order to meet future requirements for emission reduction and fuel economy a variety of concepts are available for gasoline engines. In the recent past new pathways have been found using alternative fuels and fuel combinations to establish cost optimized solutions. The presented concept for a SI-engine consists of combined injection of gasoline and hydrogen. A hydrogen enriched gas mixture is being injected additionally to gasoline into the engine manifold. The gas composition represents the output of an onboard gasoline reformer. The simulations and measurements show substantial benefits to improve the combustion process resulting in reduced cold start and warm up emissions and optimized part load operation. The replacement of gasoline by hydrogen-rich gas during engine start leads to zero hydrocarbons in the exhaust gas.
Technical Paper

Influence of Water-Diesel Fuel Emulsions and EGR on Combustion and Exhaust Emissions of Heavy Duty DI-Diesel Engines equipped with Common-Rail Injection System

2003-10-27
2003-01-3146
In this paper we investigate the effect of the introduction of water in the combustion chamber of a DI-diesel engine on combustion characteristics and pollutant formation, by using water-diesel fuel emulsions with three distinct water amounts (13%, 21% and 30%). For the measurements we use a modern 4-cylinder DI-diesel engine with high-pressure common rail fuel injection and EGR system. The engine investigations are conducted at constant speed in different operating points of the engine map with wide variations of injection setting parameters and EGR rate. The main concern refers to the interpretation of both measured values and relevant thermodynamic variables, which are computed with analytical instruments (heat release rate, ignition delay, reciprocal characteristic mixing time, etc). The analysis of the measured and computed data shows clear trends and detailed evaluations on the behavior of water-diesel fuel emulsions in the engine process are possible.
Technical Paper

Characterization of the Combustion in a Direct Injection Spark Ignition Engine

2002-03-04
2002-01-0834
The physical behavior of the combustion process in a jet-guided direct injection spark ignition engine has been investigated with three different measurement techniques. These are flame visualization by use of endoscopy, ion-current sensing at 16 different locations in the combustion chamber and the estimation of the flame temperature as well as soot concentration based on multi-wavelength-pyrometry. The results of all these measurement techniques are in good agreement between each other and give a coherent picture of the physical behavior of the combustion process and make it possible to characterize the main influence parameters on combustion. This serves as a basis for validation and improvement of simulation tools for the engine thermodynamics and combustion.
Technical Paper

Characterization and Phenomenological Modeling of Mixture Formation and Combustion in a Direct Injection Spark Ignition Engine

2002-03-04
2002-01-1138
A phenomenological model for heat release rate predictions taking into account the characteristic processes inside a direct injection gasoline engine is presented. Fuel evaporation and preparation as well as the specifics of premixed and mixing controlled combustion phase are regarded. Only a few model constants need to be set which have been fit empirically for the application in a one-cylinder research engine. This jet guided direct injection gasoline engine employs a modern common-rail injection system and runs predominantly in stratified mode. The model allows the prediction of the influence of numerous parameter variations, e.g. injection-ignition phasing, load, engine speed, swirl, etc. on the combustion process. Furthermore efficient simulations can be carried out without using expensive three-dimensional CFD (computational fluid dynamics) calculations.
Technical Paper

Influence of EGR on Combustion and Exhaust Emissions of Heavy Duty DI-Diesel Engines Equipped with Common-Rail Injection Systems

2001-09-24
2001-01-3497
At the Internal Combustion Engines and Combustion Laboratory of the Swiss Federal Institute of Technology in Zurich we are currently developing low emission strategies for heavy duty diesel engines that engine manufacturers can implement to meet stringent emissions regulations. The technologies being studied include high-pressure fuel injection (with common-rail injection system), multiple injection strategies (with pilot or post injections), turbo charging, exhaust gas recirculation (cooled EGR), oxygenated fuels and the optimization of the air management system. This paper focuses on the effects of exhaust gas recirculation (cooled EGR) in combination with very high injection pressure. Measurements were carried out on a heavy-duty diesel single-cylinder research engine equipped with a modern common rail fuel injection. The engine investigations were conducted in different operating points in the engine map covering wide speed and load ranges.
Technical Paper

Characterization of Diesel Particulate Emissions in Heavy-Duty DI-Diesel Engines with Common Rail Fuel Injection Influence of Injection Parameters and Fuel Composition

2001-09-24
2001-01-3573
The findings presented in this paper result from a collaboration between two Federal Laboratories in Switzerland. In this research project the characteristics of the particulates from internal combustion engines were investigated in detail. Measurements were carried out on a single-cylinder research engine focusing on exhaust particulate matter emissions. The single-cylinder diesel engine is supercharged and features a common-rail direct injection system. This work analyzes the influence of fuel properties and injection parameters on the particulate number size distribution. For the fuel composition, five different fuels including low sulfur diesel, zero-sulfur and zero-aromatics diesel, two blending portions of oxygenated diesel additive and rapeseedmethylester were used. For the injection parameters the injection pressure, the start of injection and the fuel amount in the pilot- and in the post-injection phases were varied.
Technical Paper

Characterization of Mixture Formation in a Direct Injected Spark Ignition Engine

2001-05-07
2001-01-1909
We have performed simulations and experiments to characterize the mixture formation in spray-guided direct injected spark ignition (DISI) gasoline engines and to help to understand features of the combustion process, which are characteristic for this engine concept. The 3-D computations are based on the KIVA 3 code, in which basic submodels of spray processes have been systematically modified at ETH during the last years. In this study, the break-up model for the hollow-cone spray typical for DISI engines has been validated through an extended comparison with both shadowgraphs and Mie-scattering results in a high-pressure-high-temperature, constant volume combustion cell at ambient conditions relevant for DISI operation, with and without significant droplet evaporation. Computational results in a single-cylinder research engine have been then obtained at a given engine speed for varying load (fuel mass per stroke), swirl and fuel injection pressure.
Technical Paper

Natural Gas Engines for Cogeneration: Highest Efficiency and Near-Zero-Emissions through Turbocharging, EGR and 3-Way Catalytic Converter

2000-10-16
2000-01-2825
Combustion engines for decentralized power generation or cogeneration in general, are subject to increasingly stringent pollutant emissions regulations. Motivated by the Europe-;wide lowest allowable NOx levels in Switzerland - particularly in the Zurich metropolitan area with 50 mg/Nm3 at 5% O2 - and in close cooperation with industry, the I.C. Engines and Combustion Laboratory (LVV) of the Swiss Federal Institute of Technology Zurich (ETHZ) has investigated some new operating concepts and engine processes in order to overcome the dilemma between low emissions and high efficiency, which is usually encountered in engine optimization. Our final approach thereby involves the Exhaust Gas Recirculation (EGR) combined with stoichiometric mixture (λ = 1) and a 3-way catalytic converter. The engine is supercharged and the intake mixture aftercooled for high power density and thermal efficiency.
Technical Paper

Oxygenated Fuels for Particulate Emissions Reduction in Heavy-Duty DI-Diesel Engines with Common-Rail Fuel Injection

2000-10-16
2000-01-2885
Oxygenated fuel additives are currently an important research topic for particulate emissions reduction in diesel engines with direct injection (DI) to meet future emission regulations. In this work more than twenty oxygenated hydrocarbons from the literature were considered as diesel fuel additives. Butylal (an acetal compound, chemical formula C9H20O2) offers significant advantages over most other oxygenates in that its physical properties are very close to those of common diesel fuel. Wear scar measurements were conducted to evaluate the lubricity characteristics of diglyme (C6H14O3), ethyldiglyme (C8H18O3), butylal and different diesel-butylal mixtures. The results reveal the low lubricity of all oxygenated compounds. Thus, for the engine tests, a lubricity improver has been added to the diesel-butylal mixtures.
Technical Paper

Analysis of Factors Influencing Particulate Matter Emissions of a Compression-Ignition Direct-Injection Engine

1999-10-25
1999-01-3492
The relative amounts of heat released by premixed and by diffusion controlled combustion is varied in a compression-ignition engine run on the test bench through variation of four operating parameters. Exhaust gas is led to a differential mobility particle sizer and to filters that are loaded for gravimetric analysis. Particle size distributions are acquired in the 16÷630 nm range of electrical mobility diameters. Opacity readings of the exhaust gas are taken, cylinder pressure is indicated, a value for the combustion noise is computed; gaseous emissions are recorded and heat release rates based on cylinder pressure analysis are evaluated. Two full factorial experiments at 2 bar bmep 2000 rpm are run as 24 combinations of four factors: Injection pressure 400 and 1200 bar, with and without pilot injection, 1/3 and 1/4 mass-fraction exhaust gas recirculation, late, middle and early start of injection.
Technical Paper

Combustion Features and Emissions of a DI-Diesel Engine with Air Path Optimization and Common Rail Fuel Injection

1998-08-11
981931
Emission and performance parameters of a medium size, and medium speed D.I. diesel engine equipped with a Miller System, a new developed High Pressure Exhaust Gas Recirculation System (HPEGR), a Common Rail (CR) system and a Turbocharger with Variable Turbine Geometry (VTG) have been measured and compared to the standard engine. While power output, fuel consumption, soot and other emissions are kept constant, nitric oxide emissions could be reduced by 30 to 50% depending on load and for the optimal combination of methods. Heat release rate analysis provides the reasons for the optimised engine behaviour in terms of soot and NOx emissions: The variable Nozzle Turbocharger helps deliver more oxygen to the combustion process (less soot) and lower the peak gas temperature (less NOx).
Technical Paper

Modeling of Ignition and Early Flame Development with Respect to Large Diesel Engine Simulation

1998-05-04
981451
A recently developed auto-ignition model based on a single transport equation in combination with a reduced kinetic scheme has been validated and tested in combination with a cascade jet and droplet breakup model. The validation has been performed by comparing ignition locations and delays for various thermodynamic conditions with experimental data from a high-pressure combustion cell. Also for medium-size diesel engine applications, predictions of ignition delay are in good agreement with experimental observations. In addition, a new approach to the modeling of the early flame development in diesel engine combustion is introduced. The reaction rate in the transition phase from the premixed to the mixing-controlled combustion mode is determined by means of a sub-grid scale model, which describes the evolution of a turbulent diffusion flame. The model has been tested during the early combustion phase of a medium-size, medium-speed DI diesel engine.
Technical Paper

A Computational Investigation of Unsteady Heat Flux Through an I.C. Engine Wall Including Soot Layer Dynamics

1997-02-24
970063
This paper deals with the influence of a wall soot layer of varying thickness on the unsteady heat transfer between the fluid and the engine cylinder wall during a full cycle of a four-stroke Diesel engine operation. For that purpose a computational investigation has been carried out, using a one-dimensional model of a multi-layer solid wall for simulating the transient response within the confinement of the combustion chamber. The soot layer is thereby of varying thickness over time, depending on the relative rates of deposition and oxidation. Deposition is accounted for due to a thermophoretic mechanism, while oxidation is described by means of an Arrhenius type expression. Results of the computations obtained so far show that the substrate wall temperature has a significant effect on the soot layer dynamics and thus on the wall heat flux to the combustion chamber wall.
Technical Paper

Reduction of NOx Emissions of D. I. Diesel Engines by Application of the Miller-System: An Experimental and Numerical Investigation

1996-02-01
960844
Emissions and performance parameters of a medium size, medium speed D.I. diesel engine with increased charge air pressure and reduced but fixed inlet valve opening period have been measured and compared to the standard engine. While power output and fuel consumption are slightly improved, nitric oxide emissions can be reduced by up to 20%. The measurements confirm the results of simulations for both performance and emissions, for which a quasidimensional model including detailed chemistry for nitric oxide prediction has been developed.
X